Software Downloads

Scanivalve develops and provides several software utilities for operating, calibrating, and maintaining Scanivalve products. All executables and installers require a Windows Operating System.

Current version and date of release can be found under each software. Software change logs can be found in the back of each user manual. For any older software versions or documentation on obsolete software, please visit the obsolete documentation archive page. 

General Software and Utilities

ScanTel

ScanTel is Scanivalve’s general communication software that supports any Ethernet enabled Scanivalve module, such as the DSA, MPS, DTS, DSM, ERAD, and ENCL. This program can be used for general configurations, data collecting using ASCII or Binary format, converting binary data to ASCII, and module troubleshooting. Scanivalve utilizes a TCP/IP connection to Scanivalve modules using port 23.

Current version: 1.08
Released: November 2024

Sensor Replacement Utility (SRU)

Sensor Replacement Utility, or SRU, is used for replacing or changing sensor coefficients in DSA or ZOC modules. After physically replacing or changing a sensor(s) in a module, SRU can be used to save single sensor coefficients and upload new coefficients for the newly installed sensor.

Current version: 1.04
Released: June 2019

LabVIEW® Based Programs and Development Examples

DSALink4

DSALink4 is a simple and easy to use program written specifically in LabVIEW® for DSA3200/3300 and DSA-PTP scanners. DSALink4 is capable of displaying and collecting data from a DSA Scanner with an easy-to-use graphical user interface. The download also includes the VIs used to build the program which can be used as examples if integrating a DSA modules into a current LabVIEW® environment.

IMPORTANT: This program does not work with DSAENCL or DSA5000 scanners.

Current version: 1.01
Released: April 2018

MPSLink

MPSLink is a simple and easy to use program written specifically in LabVIEW® for MPS4200 scanners (32 or 64 channel). MPSLink is capable of displaying and collecting data from up to eight (8) MPS4200 series scanners with an easy-to-use graphical user interface. The download also includes the VIs used to build the program which can be used as examples if integrating a MPS modules into a current LabVIEW® environment.

Current version: 1.01
Released: April 2022

MPS4232Link

MPS4232Link is a program written specifically in LabVIEW® for MPS4232, 32-channel scanners. MPS4232Link is capable of displaying and collecting data from the MPS4232 scanners with an easy-to-use graphical user interface. Only one module can be connected per instance. The download also includes the VIs used to build the program which can be used as examples if integrating a MPS modules into a current LabVIEW® environment.

IMPORTANT: The standalone program will not work with the 64 channel MPS4264.

Current version: 1.00
Released: May 2022

Legacy LabVIEW® Development Kit

Scanivalve’s Legacy LabVIEW® Development Kit (SLDK) is intended for uses who would like to write their own software interface to operate MPS, DSA, ERAD, DSM, DTS, or ENCL devices in a LabVIEW® environment. This kit contains several sub VIs and examples to aid in communication and code writing, as well as some full example programs (DSALink4 and MPSLink) and simple executable utilities.

IMPORTANT: For DSA5000 or MPS4232 scanners, please see DSA5000Link or MPS4232Link, respectively. Legacy VIs in this kit will have limited to no functionality with the DSA5000 and MPS4232 series pressure scanners.

Current version: Rev B
Released: July 2019

Calibration Software

CalExpress

CalExpress is the latest Scanivalve calibration software that supports automated or manual calibrations and validations for the 5000 series of scanners (DSA5000). This program performs two basic tests: Calibrations (calibrating and creating new coefficient tables), and Validation (validating any previously performed calibration or current coefficients). Readable reports are generated after any completed validation. Successful calibrations will save and store all coefficients (pre and post process) for easy archival. Note: this program does not perform calibrations on MPS, ZOC, or DSA3200 series scanners. 

Current version: 1.00
Released: February 2024

PressCal

PressCal is Scanivalve’s general calibration software that supports automated or manual calibrations and validations for several Scanivalve modules, including DSA, ZOC and MPS4100 series scanners (all analog modules require DSM, ERAD or ENCL) . This program can perform three tasks: As-Received Validations (validating the current coefficient tables in the module), Calibrations (calibrating and creating new coefficient tables), and Post-Calibration Validation (validating any previously performed calibration). Readable reports are generated after any completed validation. Successful calibrations will save and store all coefficients (pre and post process) for easy archival. PressCal replaced DSA3000 FieldCal, DSA3200 FieldCal, and DSM FieldCal. Note: this program does not perform calibrations on MPS4200 series scanners. Calibrations are native to internal software of these devices. 

Current version: 4.09
Released: September 2020

TempCal

TempCal is Scanivalve’s general calibration software that supports automated or manual calibrations and validations for DTS series thermocouple scanners. This program can perform three tasks: As-Received Validations (validating the current coefficient tables in the module), Calibrations (calibrating and creating new coefficient tables), and Post-Calibration Validation (validating any previously performed calibration). Readable reports are generated after any completed validation.  Note: DTS Calibration Kits are required to perform any validation or calibration with TempCal. 

Current version: 1.04
Released: January 2017